Function Analysis of Industrial Robot under Cubic Polynomial Interpolation in Animation Simulation Environment.

You Li; Juan Wang; Yiming Ji

doi:10.9781/ijimai.2020.11.012

Authors

You Li Wuchang University of Technology
Juan Wang Wuchang University of Technology
Yiming Ji Zhongnan University of Economics and Law

DOI:

https://doi.org/10.9781/ijimai.2020.11.012

Keywords:

Robotics, Polishing Robot Operating Arm, Cubic Polynomial Interpolation, Trajectory Planning, Kinematic Model, Multi-body Dynamics Simulation Software

Abstract

In order to study the effect of cubic polynomial interpolation in the trajectory planning of polishing robot manipulator, firstly, the articular robot operating arm is taken as the research object, and the overall system of polishing robot operating arm with 7 degrees of freedom is constructed. Then through the transformation of space motion and pose coordinate system, Denavit-Hartenberg (D-H) Matrix is introduced to describe the coordinate direction and parameters of the adjacent connecting rod of the polishing robot, and the kinematic model of the robot is built, and the coordinate direction and parameters of its adjacent link are described. A multi-body Dynamic simulation software, Automatic Dynamic Analysis of Mechanical Systems (ADAMS), is used to analyze the kinematic simulation of the robot operating arm system. Finally, the trajectory of the robot manipulator is planned based on the cubic polynomial difference method, and the simulation is verified by Matrix Laboratory (MATLAB). Through calculation, it is found that the kinematic model of polishing robot operating arm constructed in this study is in line with the reality; ADAMS software is used to generate curves of the rotation angles of different joint axes and the displacement of end parts of the polishing robot operating arm changing with time. After obtaining relevant parameters, they are put into the kinematic equation constructed in this study, and the calculated position coordinates are consistent with the detection results; moreover, the polishing robot constructed in this study can realize the functions of deburring, polishing, trimming, and turning table. MATLAB software is used to generate the simulation of the movement trajectory of the polishing robot operating arm, which can show the change curve of angle and angular velocity. The difference between the angle at which the polishing robot reaches the polishing position, the change curve of angular velocity, and the time spent before and after the path optimization is compared. It is found that after path optimization based on cubic polynomial, the change curve of the polishing robot's angle and angular velocity is smoother, and the time is shortened by 17.21s. It indicates that the cubic polynomial interpolation method can realize the trajectory planning of the polishing robot operating arm, moreover, the optimized polishing robot has a continuous and smooth trajectory, which can improve the working efficiency of the robot.

Downloads

Download data is not yet available.

References

[1] L. Song, W.H. Liu, Y.M. Li, and F.H. Xin. Humidity-resistant inorganic binder for sand core making in foundry practice, China Foundry, vol. 16, no.4, pp. 267-271, 2019, doi:10.1007/s41230-019-8169-8.

[2] Y. Watanabe, T. Sugiura, H. Sato, and H. Tsuge. Fabrication of Al-Based Composites by Centrifugal Mixed-Powder Method and Their Application for Grinding Wheels, Journal of Materials Engineering and Performance, pp. 1-12, 2019, doi:10.1007/s11665-019-03917-3.

[3] Shaofei Wu. A Traffic Motion Object Extraction Algorithm, International Journal of Bifurcation and Chaos, vol. 25, no. 14, Article Number 1540039, 2015, doi:10.1142/S0218127415400398.

[4] G. Pradeep, S. K. Kumar, G. Mathivanan, and H. Praveen. Design and Fabrication of Punch Tool Arrangement to Remove Excess Base Fillings from Aluminium Die Casting, Engineering Reports, vol. 2, no. 1, pp.30- 34, 2019.

[5] T. Zhang. Weighted hand-eye calibration algorithm for robot grinding, Journal of Mechanical Engineering, vol. 54, no. 17, pp. 142, 2018.

[6] K. Subrin, S. Garnier, T. Bressac, and B. Furet. Digital chain development for sanding application with a kinematically redundant robotic system, Procedia CIRP, vol. 82, pp. 515-520, 2019, doi: 10.1016/j.procir.2019.04.063.

[7] H. Lyu, Y. Liu, J. Y. Guo, H. M. Zhang, and Z. X. Li. Tool-path generation for industrial robotic surface-based application, Advances in Manufacturing, vol. 7, no. 1, pp. 64-72, 2019, doi:10.1007/s40436-018-00246-x.

[8] W. X. Ng, H. K. Chan, W.K. Teo, and I.M. Chen. Capturing the tacit knowledge of the skilled operator to program tool paths and tool orientations for robot belt grinding, International Journal of Advanced Manufacturing Technology, vol. 91, no. 5-8, pp. 1599-1618, 2017, doi:10.1007/s00170-016-9813-8.

[9] D. Mahdy, R. Reda, N. Hamdi, and I.S.M. Khalil. Ultrasound-guided minimally invasive grinding for clearing blood clots: promises and challenges, IEEE Instrumentation and Measurement Magazine, vol. 21, no. 2, pp. 10-14, 2018.

[10] H. J. Lee, M. T. Soe, S. H. Chauhdary, S. Rhee, and M. S. Park. A data aggregation scheme for boundary detection and tracking of continuous objects in WSN, Intelligent Automation & Soft Computing, vol. 23, no. 1, pp. 135-147, 2017, doi:10.1080/10798587.2016.1183922.

[11] V. Andrean, P. Chang, and K. Lian. A review and new problems discoveryof four simple decentralized maximum power point tracking algorithms— Perturb and observe, incremental conductance, golden section search, and Newton’s quadratic interpolation, Energies, vol. 11, no. 11, pp. 2966, 2018, doi:10.3390/en11112966.

[12] E. Zubko, G. Videen, J. A. Arnold, B. MacCall, A. J. Weinberger, and Y. Shkuratov. Interpolating light-scattering properties of irregularly shaped, absorbing particles, Optics letters, vol. 43, no. 17, pp. 4308-4311, 2018, doi:10.1364/OL.43.004308.

[13] B. Zhang, and Z. Feng. The Construction Method of Interpolation Polynomial by Fractal Interpolation, International Journal of Nonlinear Science, vol. 25, no. 1, pp. 48-52, 2018.

[14] Shaofei Wu, Mingqing Wang, Yuntao Zou. Research on internet information mining based on agent algorithm, Future Generation Computer Systems, vol. 86, pp. 598-602,2018, doi:10.1016/j. future.2018.04.040.

[15] Ü. Dinçer, and M. Çevik. Improved trajectory planning of an industrial parallel mechanism by a composite polynomial consisting of Bézier curves and cubic polynomials, Mechanism and Machine Theory, vol. 132, pp. 248-263, 2019, doi: 10.1016/j.mechmachtheory.2018.11.009.

[16] L. Li, Y. Zhang, M. Ripperger, J. Nicho, and A. Fumagalli. Autonomous object pick-and-sort procedure for industrial robotics application, International Journal of Semantic Computing, vol. 13, no. 2, pp. 161-183, 2019, doi:10.1142/S1793351X19400075.

[17] J. R. Bourne, E.R. Pardyjak, and K.K. Leang. Coordinated bayesian-based bioinspired plume source term estimation and source seeking for mobile robots, IEEE Transactions on Robotics, vol. 35, no. 4, pp. 967-986, 2019, doi: 10.1109/TRO.2019.2912520.

[18] S. H. Kim, and J. H. Park. The Effect of Occupation-Based Bilateral Upper Extremity Training in a Medical Setting for Stroke Patients: A Single-Blinded, Pilot Randomized Controlled Trial, Journal of Stroke and Cerebrovascular Diseases, vol. 28, no. 12, pp. 104335, 2019.

[19] R. Hou, L. Wang, Q. Gao, Y. Hou, and C. Wang. Indirect adaptive fuzzy wavelet neural network with self-recurrent consequent part for AC servo system, ISA transactions, vol. 70, pp. 298-307, 2017, doi:10.1016/j. isatra.2017.04.010.

[20] H. Yan, Y. Cao, and J. Yang. Statistical tolerance analysis based on good point set and homogeneous transform matrix, Procedia Cirp, vol. 43, pp. 178-183,2016, doi: 10.1016/j.procir.2016.02.042.

[21] R. R. Serrezuela, A. F. C. Chavarro, M. A. T. Cardozo, A. L. Toquica, and L. F. O. Martinez. Kinematic modelling of a robotic arm manipulator using Matlab, ARPN Journal of Engineering and Applied Sciences, vol. 12, no. 7, pp. 2037-2045, 2017.

[22] I. Pavlenko, J. Trojanowska, O. Gusak, V. Ivanov, J. Pitel, and V. Pavlenko. Estimation of the reliability of automatic axial-balancing devices for multistage centrifugal pumps, Periodica Polytechnica Mechanical Engineering, vol. 63, no. 1, pp. 52-56, 2019.

[23] X. H. Li, H. B. Yu, M. Z. Yuan, Y. Yin, and H. Pan. Study on the linear dynamic model of shield TBM cutterhead driving system, IECON 2011- 37th Annual Conference of the IEEE Industrial Electronics Society, pp. 3864-3871, 2011.

[24] Z. Liu, J. Xu, Q. Cheng, Y. Zhao, and C. Yang. Trajectory planning with minimum synthesis error for industrial robots using screw theory, International Journal of Precision Engineering and Manufacturing, vol. 19, no. 2, pp. 183-193, 2018.

[25] S. Wu, M. Wang, Y. Zou. Bidirectional cognitive computing method supported by cloud technology, Cognitive Systems Research, vol. 52, pp. 615-621, 2018, doi: 10.1016/j.cogsys.2019.03.015.

[26] D. Di Vito, C. Natale, and G. Antonelli. A comparison of damped least squares algorithms for inverse kinematics of robot manipulators, IFAC-PapersOnLine, vol. 50, no. 1, pp. 6869-6874, 2017, doi:10.1016/j. ifacol.2017.08.1209.

[27] S. Pellegrinelli, A. Orlandini, N. Pedrocchi, A. Umbrico, and T. Tolio. Motion planning and scheduling for human and industrial-robot collaboration, CIRP Annals, vol. 66, no. 1, pp. 1-4, 2017, doi:10.1016/j. cirp.2017.04.095.

[28] S. Wu, Nonlinear information data mining based on time series for fractional differential operators, Chaos, vol. 29, pp. 013114, 2019, doi:10.1063/1.5085430.

[29] L. Ji, H. Wang, T. Zheng, and X. Qi. Motion trajectory of human arms based on the dual quaternion with motion tracker, Multimedia Tools and Applications, vol. 76, no. 2, pp. 1681-1701, 2017, doi:10.1007/s11042-015- 3099-y.

[30] J. Xu, H. Yang, M. Liu, J. Tian, and B. Liu. Research on winding trajectory planning for elbow pipe based on industrial robot, The International Journal of Advanced Manufacturing Technology, vol. 93, no. 1-4, pp. 537- 545, 2017, doi:10.1007/s00170-017-0568-7.

[31] R. Walambe, N. Agarwal, S. Kale, and V. Joshi. Optimal trajectory generation for car-type mobile robot using spline interpolation, IFAC-PapersOnLine, vol. 49, no. 1, pp. 601-606, 2016, doi:10.1016/j. ifacol.2016.03.121.

[32] H. M. Alwan, and Z. H. Rashid. Motion Control of Three Links Robot Manipulator (Open Chain) with Spherical Wrist, Al-Khwarizmi Engineering Journal, vol. 15, no. 2, pp. 13-23, 2019, doi:10.22153/ kej.2019.12.001.

[33] K. Leng, Y. Bi, L. Jing, H. Fu, I. Van Nieuwenhuyse. Research on agricultural supply chain system with double chain architecture based on blockchain technology, Future Generation Computer System, vol. 86, pp. 641-649, 2018, doi: 10.1016/j.future.2018.04.061.